Jaybee Industries logoJaybee Industries · Delhi, Noida, Gurugram, Ghaziabad, Faridabad Toll-free 1800 309 9948

Posts · Delhi NCR

DISCOM metering, CT/PT and the transformer: coordination on NCR projects

Published by Jaybee Industries

The meter belongs to the licensee. The transformer belongs to you. The two still have to be designed as one arrangement, or someone will be cutting concrete later.

On industrial and large commercial projects in Delhi NCR, the incoming metering is specified and often supplied or tightly prescribed by the distribution licensee. That licensee changes with the location: different parts of Delhi, Noida, Greater Noida and Ghaziabad are not served by the same utility, and each has its own metering practice. The transformer, meanwhile, is a plant or building asset that you purchase. If the two are designed in isolation, the usual results are a metering kiosk that has no home, a CT ratio that does not match the expected load, or a cable schedule that assumes a terminal arrangement the transformer does not have.

This article is for project engineers and consultants. It does not replace the licensee’s current circulars or your consultant’s design. It is about the questions that should be closed before the transformer drawing is approved.

Find out the metering scheme before the GA is frozen

Early in the project, obtain from the licensee or from your electrical consultant a clear statement of:

  • Where metering will sit: in a licensee kiosk, in a room, on a structure, or in another prescribed arrangement.
  • Whether metering current transformers and, where applicable, potential transformers are in the licensee’s panel, on the incoming structure, or required as bushing or separately mounted CTs associated with the transformer.
  • The likely CT ratio and accuracy class the licensee expects for your sanctioned load, and who is responsible for supplying those CTs.
  • Clearances, locking, earthing and access the licensee requires around the metering equipment.

Until those points are written down, it is risky to treat the transformer GA as final. A late request for a different HV terminal orientation, a longer cable box, or space for a kiosk on the same plinth is how delivery dates slip.

Match the ratios to the real load

Metering CTs should suit the sanctioned load and the way the plant will actually run, including a planned expansion if one is already approved. A ratio chosen on a hopeful connected-load figure can leave the meter working at the bottom of its range, or can force a change when the sanction is revised. This is a conversation between your consultant and the licensee; the transformer manufacturer needs the outcome, not a guess. If bushing CTs or a particular secondary rating are required on the transformer itself, put them in the enquiry as a numbered requirement, not as a remark in an email two weeks after the order.

Space, earthing and cable routes

A metering kiosk or room needs a home on the plot plan: access for the licensee, a cable route that does not fight the transformer radiators or doors, and an earthing arrangement that meets the scheme your consultant has drawn. On tight NCR plots, this is often the item that gets pushed into a corner. Place it on the same drawing as the transformer plinth, the incoming structure and the main board, and keep that drawing consistent through civil work.

What to include in the transformer enquiry

  • The project location and the name of the distribution licensee, if you know it.
  • Incoming voltage, sanctioned or applied load, and the metering scheme as currently understood.
  • Any requirement for bushing CTs, a particular terminal arrangement, or space on the HV side for licensee equipment.
  • A layout showing the transformer, the proposed metering position and the cable routes.

If some of this is still being discussed with the licensee, say what is agreed and what is open. A manufacturer can allow a defined option for a short time; they cannot design around a blank.

Jaybee Industries has manufactured transformers since 1981, with plants at Bathinda, Kirpalpur (Nalagarh) and Ambala, and works with consultants and industrial buyers across Delhi NCR. Send the metering note with the electrical duty, and mention “NCR metering coordination” on the enquiry. We will design against the agreed scheme and will not publish a price in place of a written offer.

Send your enquiry

Call toll-free 1800 309 9948, message us on WhatsApp at +91 98162 95407, or email info@jaybeeindustries.com. Mention this article and your site location so the right team responds. We reply with technical options; we do not publish prices, and every offer is prepared for your specification.

Related pages on this site

Request a quote Call 1800 309 9948 WhatsApp +91 98162 95407 info@jaybeeindustries.com

← All posts

CallWhatsAppGet a quote